Not a good start this year...

[Midnight_Rush]

Well.... Went for a nice cruise Sat afternoon to Hampton beach with a few car peeps. Had a great drive there and well coming back I think I blew my motor... I will know more today or tomorrow. but I don't think it's going to be good. I had to tow it to Ballistics. If thats the case... my car will not be at any subie meets, WBM, Import Face off.... :unamused:

[katie.ims]

get well soon </3

[Diztracted]

OMG!!!!! Nooooooooo!!!!!!!!!!!!!!!!!!!!

[Diztracted]

Keep us posted on what happens gal.. hang in there!

[Midnight_Rush]

yeah I will deff let you know when I find out. I was planning on rebuilding my motor in the fall. after I finished my interior... but I guess it's reversed... Im not really ready to rebuild the motor.. I hope it's not too bad..

[drdabbles]

Hopefully something simple & inexpensive. :up:

[Demetry]

I was at Scott's on Monday night, sounds like a rod/bearing issue to me. But he wasn't quite sure at the time. We went to scan the code and it was erased at some point, started it for a couple seconds and turned it off...I'm no expert though.


GL though, just think, only thing after motor is transmission :unamused:

[HipsterDoofus]

ohno :(

im sorry about all that

[Hero]

aw man :(

[Evoeater]

Im sorry to hear that....:(

[Bu11dogg2]

http://www.briancrower.com/makes/subaru/ej205.shtml


It's what I got :)

[Midnight_Rush]

thanks guys.. I hope once we figure out whats wrong, it will only take a month to fix.?? I will deff check that out again Randy! maybe I should be carefull what i wish for since I was all about rebuilding my motor when I took it out of storage.. im just not really ready at this point and time.. lmao

I hope thats all thats wrong with it Chad.... but then again If im fixing the motor now I may as well rebuild everything... annnnd then cry since i will have to build my tranny. ohhh im going to be broke.. so much for my suede interior and two 10" subs.... lol

[Bu11dogg2]

took 2 months to build mine

[Robk0000]

^stop attempting to hijack the thread randy.

[drdabbles]

thanks guys.. I hope once we figure out whats wrong, it will only take a month to fix.?? I will deff check that out again Randy! maybe I should be carefull what i wish for since I was all about rebuilding my motor when I took it out of storage.. im just not really ready at this point and time.. lmao

I hope thats all thats wrong with it Chad.... but then again If im fixing the motor now I may as well rebuild everything... annnnd then cry since i will have to build my tranny. ohhh im going to be broke.. so much for my suede interior and two 10" subs.... lol

Well, you can always repair what's broken now and start collecting parts for a build over the summer. That way you still have a car to roll around in.

[batorr]

That happend to mine. it ended up being a good thing tought. I put a brand new sti short block in it. Big difference. If it is your motor I believe the sti block is around the same price as a wrx. Unfortunately when all said and done everything cost me around $3,400 :(

[Demetry]

That happend to mine. it ended up being a good thing tought. I put a brand new sti short block in it. Big difference. If it is your motor I believe the sti block is around the same price as a wrx. Unfortunately when all said and done everything cost me around $3,400 :(


ouch, almost as much as I just spent on my transmission :unamused:

[Gearhead Geek]

Ouch, sorry to hear. Everybody's cars going boom lately has me worried, especially with my history rofl.
Hope it gets worked out quick. As has been mentioned, I would suggest that if it's nothing too huge, fix it in the interm to save you from being without a car for a long time.

[Demetry]

Ouch, sorry to hear. Everybody's cars going boom lately has me worried, especially with my history rofl.
Hope it gets worked out quick. As has been mentioned, I would suggest that if it's nothing too huge, fix it in the interm to save you from being without a car for a long time.


you wont be ROFL if you blow *****, lol.

BTW, Car sounded good today :)

[Gearhead Geek]

you wont be ROFL if you blow *****, lol.

BTW, Car sounded good today :)

Oh trust me, if I blow something up I will. After everything I broke on the Civic I learned to just laugh about it.

And ty :D
Perhaps we can make a new video for the website to show what the catted system sounds like :)

[Demetry]

Oh trust me, if I blow something up I will. After everything I broke on the Civic I learned to just laugh about it.

And ty :D
Perhaps we can make a new video for the website to show what the catted system sounds like :)

Yeah, we will soon. I would like that. Have had a couple requests. Move that to PM or text, don't want to get in trouble :hide:.

Back to her motor....

[Gearhead Geek]

Yeah, we will soon. I would like that. Have had a couple requests. Move that to PM or text, don't want to get in trouble :hide:.

Back to her motor....

Uhh, ya, I meant, uhh, a video of your truck running over a Mustang. Ya, that's it! :D

[Gearhead Geek]

So just curious, what kind of driving conditions were you doing when it went? Was there overboost or something or were you just putting along when it went poof?

[Rooster]

Well.... Went for a nice cruise Sat afternoon to Hampton beach with a few car peeps. Had a great drive there and well coming back I think I blew my motor... I will know more today or tomorrow. but I don't think it's going to be good. I had to tow it to Ballistics. If thats the case... my car will not be at any subie meets, WBM, Import Face off.... :unamused:


I saw you and Brian on the side of the road. :( I would have stopped but we was really late as it was...

Good luck!

[RCKSTR]

keep me updated pj :spin: let me know if you need some help finding stuff because thats what I do :up:

[civic si hb]

Oh trust me, if I blow something up I will. After everything I broke on the Civic I learned to just laugh about it.

And ty :D
Perhaps we can make a new video for the website to show what the catted system sounds like :)


Mine will blow long before yours does....

I make much TQS and Horse pressures than you do :lol:

[Gearhead Geek]

I make much TQS and Horse pressures than you do :lol:

For now... :D

[Seraphinwolf]

Sorry to hear Ashley. I vote temp fix and go for the 257! It'll be all worth it in the end.
And yes Randy is a cheater McCheatieface.

[wrxtuner82]

This is also a very sad thread...I don't like all these sad threads :( if the motor is blown, I vote you pull out all the stops and buy the Crawford Performance 2.7 big block ;)

[Seraphinwolf]

Connor you know that's like $7k for just the block right, or something like that? Rediculous! Worth every penny but still rediculous!

[Midnight_Rush]

So just curious, what kind of driving conditions were you doing when it went? Was there overboost or something or were you just putting along when it went poof?

Well I was trying to keep up with Brian with 441whp and Brandon that has I think around 400whp. So I was pushing my car...I never slam or drop my gears since I dont want to bust my tranny. nor do I redline it... but I was in 4th gear hauling a$$, I never went over 7rpm.. Kinda like in 4th gear going 65 to 90 slow down put it on 5th, till Brian passed me I put it back in 4th hit the gas hit around 100 rmh when I caught up slowed down... just kinda tooling on the highway. Nothing too extreme, not like I was rallying... I think it was just the torque when i had it in 4th gear for a while..

I felt the car lose a little bit of power so I rolled my windows up and turned off the radio. there was a slapping noise, as i was getting ready to pull over i was losing more power, when i got to the side of the road my car died. would not start back up, when i tried starting it up the motor was shaking like something was off balance. when we fianlly started it there was a banging noise so we turned it off... ::sigh::

I saw you and Brian on the side of the road. :( I would have stopped but we was really late as it was... there was a few subies that passed us. was a new impreza outback sprot towing a dirtbike honked and waked at us... :unamused: I thought it was Randy at first. lol

Good luck!

keep me updated pj :spin: let me know if you need some help finding stuff because thats what I do :up:

I will deff keep you updated. your the master of parts! lol :D

[HipsterDoofus]

at least you still have the green leggy, right?



:hide:

[wrxtuner82]

Connor you know that's like $7k for just the block right, or something like that? Rediculous! Worth every penny but still rediculous!

$14,500 (believe me, every time I think of Iraq, I'm thinking Crawford long block stroker package)

Worth every penny.....I want two

[civic si hb]

I don't know much about your car but a few questions for ya?

Are you on the stock TD04 or a upgraded turbo?

Also what kind of HP and TQ are you putting down?

Finally how many miles on the car itself?

Thanks
Rob

[Gearhead Geek]

Well I was trying to keep up with Brian with 441whp and Brandon that has I think around 400whp. So I was pushing my car...I never slam or drop my gears since I dont want to bust my tranny. nor do I redline it... but I was in 4th gear hauling a$$, I never went over 7rpm.. Kinda like in 4th gear going 65 to 90 slow down put it on 5th, till Brian passed me I put it back in 4th hit the gas hit around 100 rmh when I caught up slowed down... just kinda tooling on the highway. Nothing too extreme, not like I was rallying... I think it was just the torque when i had it in 4th gear for a while..

I felt the car lose a little bit of power so I rolled my windows up and turned off the radio. there was a slapping noise, as i was getting ready to pull over i was losing more power, when i got to the side of the road my car died. would not start back up, when i tried starting it up the motor was shaking like something was off balance. when we fianlly started it there was a banging noise so we turned it off... ::sigh:: Still new to Subarus and their array of funny noises, but sounds to me like some piston slap. I'll keep my fingers crossed for you that it's just a spun rod bearing or something that can easily be bandaided for the time being :)

[Diztracted]

Well I was trying to keep up with Brian with 441whp and Brandon that has I think around 400whp. So I was pushing my car...I never slam or drop my gears since I dont want to bust my tranny. nor do I redline it... but I was in 4th gear hauling a$$, I never went over 7rpm.. Kinda like in 4th gear going 65 to 90 slow down put it on 5th, till Brian passed me I put it back in 4th hit the gas hit around 100 rmh when I caught up slowed down... just kinda tooling on the highway. Nothing too extreme, not like I was rallying... I think it was just the torque when i had it in 4th gear for a while..

I felt the car lose a little bit of power so I rolled my windows up and turned off the radio. there was a slapping noise, as i was getting ready to pull over i was losing more power, when i got to the side of the road my car died. would not start back up, when i tried starting it up the motor was shaking like something was off balance. when we fianlly started it there was a banging noise so we turned it off... ::sigh::


:( That hurts. I definitely don't know much, But if you didn't redline and didn't go past 7 rpms then I don't see how you coulda blown your motor... But I'm not sure what else it could have been..

Idk. Hope things go well... Good luck!

[Midnight_Rush]

at least you still have the green leggy, right?



:hide:

Yes I still have my little leggy Im actually thinking about selling it since I have a Demo now at work. woot woot. so it's been sitting for a year :unamused: not good for the car at all....

I don't know much about your car but a few questions for ya?

Are you on the stock TD04 or a upgraded turbo?

Also what kind of HP and TQ are you putting down?

Finally how many miles on the car itself?

Thanks
Rob

Invidia Cat Back Exhaust,
TurboXS FMIC,
TurboXS BOV,
K&N short Ram Intake,
VF34 turbo,
Helix 660cc injectors,
Helix Catless up-pipe/down-pipe,
Walbro 255lp fuel pump,
Perrin turbo inlet pipe,
Perrin radiator hose,
cobb accessport,
Tuned by XXtuning
280whp (sadly)
20PSI



Still new to Subarus and their array of funny noises, but sounds to me like some piston slap. I'll keep my fingers crossed for you that it's just a spun rod bearing or something that can easily be bandaided for the time being :) ohh I hope so I will know soon.

:( That hurts. I definitely don't know much, But if you didn't redline and didn't go past 7 rpms then I don't see how you coulda blown your motor... But I'm not sure what else it could have been..

Idk. Hope things go well... Good luck!

well my timing belt could of went and that would mess up my motor. playing around too hard, torque.. so many little things...

[civic si hb]

Invidia Cat Back Exhaust,
TurboXS FMIC,
TurboXS BOV,
K&N short Ram Intake,
VF34 turbo,
Helix 660cc injectors,
Helix Catless up-pipe/down-pipe,
Walbro 255lp fuel pump,
Perrin turbo inlet pipe,
Perrin radiator hose,
cobb accessport,
Tuned by XXtuning
280whp (sadly)
20PSI



That would still make for fun daily driver... :)

How many miles on the engine and how many miles driven on with the turbo upgrade and the other toys listed above???

[Demetry]

That would still make for fun daily driver... :)

How many miles on the engine and how many miles driven on with the turbo upgrade and the other toys listed above???


Rob, she has 60,xxx miles on the car. Not sure how many of them were modded...

[Midnight_Rush]

It's not even a daily driver thats what sucks! I bought the car with around 25k on it, and right when I bought it I started modding.

[civic si hb]

It's not even a daily driver thats what sucks! I bought the car with around 25k on it, and right when I bought it I started modding.


WOW, that is really unfortunate :(

To have bearly driven the car with those miles considering the year.

Well i hope it's more on the simple and less expensive end for repairs for ya :)

Good Luck :)

[Midnight_Rush]

yeah.... still don't know whats wrong with it...

[HipsterDoofus]

no bueno :(

[2.5guy]

Ashley I'm guessing rod bearing sounds exactly like what my two motors did. If that is the case your going to want to make sure there are no scoring marks on your crank

[Subygirl8330]

im sad scott hasn't looked at ur car yet :(

[batorr]

any word on the engine yet?

[wrxtuner82]

any word on the engine yet?
:munch:

[DHGurs]

This must be a bad time of year for Subarus, motors blowing left and right, trees falling on them...

[batorr]

This must be a bad time of year for Subarus, motors blowing left and right, trees falling on them...
transmissions shattering...

[wrxtuner82]

This must be a bad time of year for Subarus,trees falling on them...
not a fan of that one....3 more weeks till she's back....hope it looks as good as before....bonus though, I got the STi wing for it.

[Demetry]

This must be a bad time of year for Subarus, motors blowing left and right, trees falling on them...

transmissions shattering...

batorr took my words...:lol:

[shtbxr22]

at least my pistons will be here today. now for reassembly. ugh! any news ashley?

[Bu11dogg2]

:munch:

[Berge56]

CUZ!! I just saw this thread! Very sorry to hear. After your post about the sound your motor was making it sounds like bearings to me. How were you oil levels???

Keep me posted on what you decide to do for a motor as I am curious. Good luck.

[Midnight_Rush]

hey guys! sorry for the late reply! Well this is how its going down.. Scott has not looked at my motor we are just going to put the 2.5 short block in with some perfomance parts.. I hope my heads are still good so I will use those. I'm trying not to think about numbers even though it's really hard not too.. I want a nice strong build that has lots of low end! but I'm trying not to limit myself at the same time..

this is what i have right now...

Invidia Cat Back Exhaust,TurboXS FMIC,TurboXS BOV, K&N short Ram Intake,VF-34 turbo, Helix 660cc injectors,Helix Catless up-pipe/down-pipe, Walbro 255lp fuel pump,Perrin turbo inlet pipe, Perrin radiator hose, cobb accessport, Tuned

this is the new mod list.
2.5 short block
CP forged Pistons ( Set with rings )
Eagel Connectin Rods
ACL Race bearings

Gates Timing belt kit
ARP Head Studs 260-4701
CROWER 02-05 WRX EJ205 62580-4 Stage 1
Perrin Boost solnoid
DW 750cc Cobb Spec Top-Feed SUB1-CS-750-4
Walbro Fuel Pump gss342 90.00 90.00
Black 02-07 WRX, 2007 STI Top-Feed Fuel Rails PSP-ENG-201BK
GTSPEC Unequal Length Header

what do you guys think? I'm trying to figure out if I should use my VF34 turbo or get a slight bigger one (again so i don't limit myself) i reaslly dont want a huge turbo since im trying to stay away from the big turbo lag.

[Seraphinwolf]

VF34 should be more than plenty shouldn't it? You'll get plenty of distance head of Brian before his 35R fully spools and he catches right up if I"m not mistaken.

[Seraphinwolf]

at least my pistons will be here today. now for reassembly. ugh! any news ashley?
Those were pretty BTW! :D

[civic si hb]

If i was to upgrade to a larger turbo I would perosnlly go no larger than a GT3071 or GT3076R. The 71R spools up a few hundred rpm quicker than the 76R. Of course still going to be lag but with the proper tune you'll still be able to enjoy a nice power band.

[Evoeater]

hey guys! sorry for the late reply! Well this is how its going down.. Scott has not looked at my motor we are just going to put the 2.5 short block in with some perfomance parts.. I hope my heads are still good so I will use those. I'm trying not to think about numbers even though it's really hard not too.. I want a nice strong build that has lots of low end! but I'm trying not to limit myself at the same time..

this is what i have right now...

Invidia Cat Back Exhaust,TurboXS FMIC,TurboXS BOV, K&N short Ram Intake,VF-34 turbo, Helix 660cc injectors,Helix Catless up-pipe/down-pipe, Walbro 255lp fuel pump,Perrin turbo inlet pipe, Perrin radiator hose, cobb accessport, Tuned

this is the new mod list.
2.5 short block
CP forged Pistons ( Set with rings )
Eagel Connectin Rods
ACL Race bearings

Gates Timing belt kit
ARP Head Studs 260-4701
CROWER 02-05 WRX EJ205 62580-4 Stage 1
Perrin Boost solnoid
DW 750cc Cobb Spec Top-Feed SUB1-CS-750-4
Walbro Fuel Pump gss342 90.00 90.00
Black 02-07 WRX, 2007 STI Top-Feed Fuel Rails PSP-ENG-201BK
GTSPEC Unequal Length Header

what do you guys think? I'm trying to figure out if I should use my VF34 turbo or get a slight bigger one (again so i don't limit myself) i reaslly dont want a huge turbo since im trying to stay away from the big turbo lag.

looks great!! Is there a timeline yet?

[Demetry]

hey guys! sorry for the late reply! Well this is how its going down.. Scott has not looked at my motor we are just going to put the 2.5 short block in with some perfomance parts.. I hope my heads are still good so I will use those. I'm trying not to think about numbers even though it's really hard not too.. I want a nice strong build that has lots of low end! but I'm trying not to limit myself at the same time..

this is what i have right now...

Invidia Cat Back Exhaust,TurboXS FMIC,TurboXS BOV, K&N short Ram Intake,VF-34 turbo, Helix 660cc injectors,Helix Catless up-pipe/down-pipe, Walbro 255lp fuel pump,Perrin turbo inlet pipe, Perrin radiator hose, cobb accessport, Tuned

this is the new mod list.
2.5 short block
CP forged Pistons ( Set with rings )
Eagel Connectin Rods
ACL Race bearings

Gates Timing belt kit
ARP Head Studs 260-4701
CROWER 02-05 WRX EJ205 62580-4 Stage 1
Perrin Boost solnoid
DW 750cc Cobb Spec Top-Feed SUB1-CS-750-4
Walbro Fuel Pump gss342 90.00 90.00
Black 02-07 WRX, 2007 STI Top-Feed Fuel Rails PSP-ENG-201BK
GTSPEC Unequal Length Header

what do you guys think? I'm trying to figure out if I should use my VF34 turbo or get a slight bigger one (again so i don't limit myself) i reaslly dont want a huge turbo since im trying to stay away from the big turbo lag.


Hate to be the one to mention it but watch the tranny or just know you may need an additional few $1000's to deal with that if you go bigger. I know from first hand experience. I'm curious on the cost of the build...sounds sweet!

[Midnight_Rush]

Civic SI: I will do some more research on turbos i'll look into both of those as well, I'm deff going to EFI when everything is installed.

how are the pistons doing Eric

EVOEATER: Im hoping it will be done before WBM in June. I dont think it would take more than a month to do. I guess it all depends if the parts come in on time ( I ordered everything today) and there are no more suprises, and I pray that my heads are okay!

Chad: thanks, I sadly have that in the back of my mind..... :/ ughh. depending where I am money wise I may just get the STI gears and not the PPG's... iiiiii dont
know.... lol

[Berge56]

Cuz save up for a 6 speed. Every one that I know who built a 5 speed borke it with a 2.5 hybrid. The 6 speeds can be found as low as 2500 for an 04-05 and you can swap in a 3.90 R160 to keep the cost down so that you don't have to upgrade to bigger hubs and brakes.

[shtbxr22]

Civic SI: I will do some more research on turbos i'll look into both of those as well, I'm deff going to EFI when everything is installed.

how are the pistons doing Eric

EVOEATER: Im hoping it will be done before WBM in June. I dont think it would take more than a month to do. I guess it all depends if the parts come in on time ( I ordered everything today) and there are no more suprises, and I pray that my heads are okay!

Chad: thanks, I sadly have that in the back of my mind..... :/ ughh. depending where I am money wise I may just get the STI gears and not the PPG's... iiiiii dont
know.... lol

got her up and running a little before 3 today. now time for break in. yuck!

[Seraphinwolf]

Save and keep eyes open for the 6 speed Ash. There are deals on them from time to time if you catch one at just the right time.

[wrxtuner82]

^The whole car or just the trans?

[Seraphinwolf]

^The whole car or just the trans?
Speaking about the swap. Sometimes a whole car too but less common.

[wrxtuner82]

I'd love to get a 6mt for mine, thought about calling Trans-medic to find out how much it'd be

[Bu11dogg2]

sounds like a great build!

330whp is all you're gonna get out of the VF34 and stock tranny :(

[Midnight_Rush]

Cuz save up for a 6 speed. Every one that I know who built a 5 speed borke it with a 2.5 hybrid. The 6 speeds can be found as low as 2500 for an 04-05 and you can swap in a 3.90 R160 to keep the cost down so that you don't have to upgrade to bigger hubs and brakes.

yeah you're right... I need to stop being cheap... I'm going to go into parts right now and see what kind of a deal they can get me for a 04-05 tranny.

got her up and running a little before 3 today. now time for break in. yuck! yeay!!!! I just need to get mine up and running now.

Save and keep eyes open for the 6 speed Ash. There are deals on them from time to time if you catch one at just the right time.
I'm going to try. I'm kinda scared to look up in Nasioc..

sounds like a great build!

330whp is all you're gonna get out of the VF34 and stock tranny :( awww... it is a good start.. but I will want more... hmmmm... I am going to look at some other turbos.

[Bu11dogg2]

18g/20g or larger

[Berge56]

go for the 20g if you go with a 2.5 and you won't be sorry. :) Also brand new 6 speeds are around 5k I believe.

[Midnight_Rush]

update: Scott and I are looking at the AMR 750R turbo.
http://www.automasteramr.com/store.php?product_id=905&make_id=1&model_id=5&category_id=12


http://www.amsracingblog.amsperformance.com/2009/06/29/ams-product-release-ams-750r-turbo-kit/

That should be pretty sweet in my subie.

[Evoeater]

new transmission? lol

[shtbxr22]

you're nuts. enjoy!! :lol:

[Seraphinwolf]

update: Scott and I are looking at the AMR 750R turbo.
http://www.automasteramr.com/store.php?product_id=905&make_id=1&model_id=5&category_id=12


http://www.amsracingblog.amsperformance.com/2009/06/29/ams-product-release-ams-750r-turbo-kit/

That should be pretty sweet in my subie.

Awww... It's a cute little turbo. :o

[Seraphinwolf]

So I take it you have settled on the 257? Gonna fully swap with full longblock or shortblock hybrid?

[Subygirl8330]

new transmission? lol


+1

[Midnight_Rush]

new transmission? lol
yeah I think im going to buy a 40-05 tranny.... not sure if I should get get a new one or search for a used... i know nasioc would prob have one... but buying used kinda scares me...

+1
sigh :unamused: lol

[Seraphinwolf]

Go used. You run as much risk used as new really. Just have Scott check it over before it goes in and you'll be fine. Or Larh's Transmission in Candia can do a quick knowledgeable check of the trans.

[Berge56]

Wow that amr turbo sounds pretty nasty! :RCKSTR: :squee:

[Berge56]

Any updates on the car Ashley?

[Midnight_Rush]

well. My car is finally in the shop! YEAY!!!!! So they should start taking things apart soon. I just ordered the Garrett 3071R turbo. That turbo should make me happy! Also! I should make a different thread for this..... but Chris at EFI stated: the 16 bit ECU in my car is restricted to the amount of power I can make, once I exceed the maximum power, I will need to go stand alone, or piggy back such as UTEC (Which we do not tune). This is my new problem right here....

[jwebsta32]

What motor are you putting in the car?

[Bu11dogg2]

Read back through the thread webstah!

[jwebsta32]

its easier for her to just say it.................now that I was forced to read it. STI 6 speed....not a 5speed please

[Midnight_Rush]

Sorry A little late on the reply... lol as you already know STI short block with my 2.0 heads. I'm trying to figure out if I really want to spend money on a STI swap.... I really dont want to change the hubs, diff, axles.... thinking bout getting just the PPG's.. i dont know... Starting to think about saving up for a house, truck, and 4-wheeler...

[Bu11dogg2]

Sorry A little late on the reply... lol as you already know STI short block with my 2.0 heads. I'm trying to figure out if I really want to spend money on a STI swap.... I really dont want to change the hubs, diff, axles.... thinking bout getting just the PPG's.. i dont know... Starting to think about saving up for a house, truck, and 4-wheeler...


you don't have to change hubs!

Here is exactly what you need with prices:


Keep your Hubs/Brakes Option 2 (Cheapest)
You will need: 06/07 USDM Transmission $4-$4400, mounts $100, 2002-2007 WRX AUTOMATIC drive shaft $500, R160, axle stubs $20, clutch plate, flywheel, throw out bearing, shift fork,Shift linkage, 04 STI axles seals, circlips, fluids, boot grease kit About $200 for all


that's for new stuff ;)

I'm going with new tranny, used shaft. Should cost me under $4500

[Midnight_Rush]

Thanks Randy! hmmm I may talk with my parts guy..

[Bu11dogg2]

If you're vigilant and buy all used I bet you can get it done for $3500.00

I'm not dealing with somone elses problems, hence why I'm buying a new tranny

[Bu11dogg2]

Check this thread out :)

http://www.newenglandsubarus.com/forums/showthread.php?t=13187

[AExiOn]

Not a good year for bug eyes :(
Mine, and a few other (all 2002) buddies' motor had died this year so far.

I'm also doing a hybrid build. But going with a vf39 to start out on. Kinda want the 5spd to some what last until I have the cash to dump on a 6spd, this whole 5spd weakness scares me on my future autocross endevors with a torque monster.

Good luck with the build!

[synergy]

Looks like i can get an 05 sti tranny rebuilt with 2 yr warrenty for 1700.
04s look like a 92k mile sti for 1800.
That sounds like way too much but I dont know what the going rate is...

Incase you go that route.

[jwebsta32]

Looks like i can get an 05 sti tranny rebuilt with 2 yr warrenty for 1700.
04s look like a 92k mile sti for 1800.
That sounds like way too much but I dont know what the going rate is...

Incase you go that route.


I would love to see where you can get an 05 sti 6 speed with a two year warranty for 1700

[synergy]

You want their number? Ill give you it man. 1-800-624-3876

I "find" Used parts for cheaper than some can imagine... I get 300zx calipers which are the same size as skyline brakes for 25$ a caliper.
Any other parts people really want for these swaps used? I bet i could get them cheaper :P

[synergy]

I got a tranny for my sentra... 120$ 37k miles 2 year warrenty/40k miles Trannys are cheap... Everything is cheap.
WRX trannys are 500-700$

[-III]

^Is that legit?

[itsmy04wrx]

You want their number? Ill give you it man. 1-800-624-3876

I "find" Used parts for cheaper than some can imagine... I get 300zx calipers which are the same size as skyline brakes for 25$ a caliper.
Any other parts people really want for these swaps used? I bet i could get them cheaper :P

Whats the name of the company? I would love to ask them about their STI 6 speeds that they are selling for $2,000.00 - $2,500.00 under what everyone else is selling them for.

[shtbxr22]

I want some brembos mr. synergy, ASAP!!!! :D

[Midnight_Rush]

If you're vigilant and buy all used I bet you can get it done for $3500.00

I'm not dealing with somone elses problems, hence why I'm buying a new tranny

Thanks for the link Randy, I have today off but when I go back to work tomorrow, Im going to talk to my parts guy and make a price list for new parts then I may get some more info about used trannys with warranty from Synergy.

Not a good year for bug eyes :(
Mine, and a few other (all 2002) buddies' motor had died this year so far.

I'm also doing a hybrid build. But going with a vf39 to start out on. Kinda want the 5spd to some what last until I have the cash to dump on a 6spd, this whole 5spd weakness scares me on my future autocross endevors with a torque monster.

Good luck with the build!

really? So it's not just me..... :unamused: How did yours bust? I am thankfull it blew close to home and not heading to maryland or somewhere far..... nice! where are you getting it tuned? ughhhh this tranny problem is starting to stress me out a little lol I was hoping to build my tranny over the winter months.. but i have this feeling if my car is done by the fall kanc run someone will be towing me home. lol i will deff keep you updated! I may make a little blog on here.

Looks like i can get an 05 sti tranny rebuilt with 2 yr warrenty for 1700.
04s look like a 92k mile sti for 1800.
That sounds like way too much but I dont know what the going rate is...

Incase you go that route.

Thanks Synergy! i deff would like to know more about this 2 year warranty tranny! do they have a website?

[AExiOn]

really? So it's not just me..... :unamused: How did yours bust?
Like this..
http://i25.photobucket.com/albums/c57/aexion/th_Artmessesupcar.jpg (http://s25.photobucket.com/albums/c57/aexion/?action=view&current=Artmessesupcar.flv)
:palm:... atleast I go out in style....

I am thankfull it blew close to home and not heading to maryland or somewhere far..... nice! where are you getting it tuned? ughhhh this tranny problem is starting to stress me out a little lol I was hoping to build my tranny over the winter months.. but i have this feeling if my car is done by the fall kanc run someone will be towing me home. lol i will deff keep you updated! I may make a little blog on here.


Lucky mine was at the office.. That was a whole lot of AAA moving the car here to there, started off with just suspention but low oil pressure + me bounceing off the rev limiter in autocross + 130K miles = I havent driven my car sense new years. Unless you count the time I drove it from north end of town to the south after putting on new shocks/springs, and control arm, and listening to my crank bearing shot with the fork wacking all around.. If ya count that, then I drove it once sense new years eve :rofl:

I am having Rob at EFI build the engine, got to the point where I just want to give it to good hands and get the damn thing done. Also right, sense I want the thing to last another 100k miles
Chris at EFI is also going to tune it. He did a great autocross map for me, made more power on stock boost then I did on cobb's stage 2 map (not stock boost)

As seen in the video, my front quarter good a good wack, and I am sure the tranny is tweaked, or hopefully the seal is just craped. I also wanted to do the tranny first before a engine build.. I guess that plan has changed. For now I will just run 560CC and a vf39. **** my tranny!!!

[Bu11dogg2]

Looks like i can get an 05 sti tranny rebuilt with 2 yr warrenty for 1700.
04s look like a 92k mile sti for 1800.
That sounds like way too much but I dont know what the going rate is...

Incase you go that route.

You want their number? Ill give you it man. 1-800-624-3876

I "find" Used parts for cheaper than some can imagine... I get 300zx calipers which are the same size as skyline brakes for 25$ a caliper.
Any other parts people really want for these swaps used? I bet i could get them cheaper :P

The gear set alone is $1500+ for the 6 speed.

add labor, shipping and misc parts I can't really see how it's possible for even a 5 speed :(

Link to shop?

[Bu11dogg2]

Found it

http://www.autosportsunlimited.com/remanufactured_european_asian_import_british_engin es.html

[DHGurs]

I found it earlier too, but it has no pricing or info about Subaru. It seems like the website is only half done.

Then again, if the prices are actually that cheap, who cares! :D

[Bu11dogg2]

all they have is a 2005 6speed

[DHGurs]

Yes they do! Only $1700 too... Ashley....

[Midnight_Rush]

Like this..
http://i25.photobucket.com/albums/c57/aexion/th_Artmessesupcar.jpg (http://s25.photobucket.com/albums/c57/aexion/?action=view&current=Artmessesupcar.flv)
:palm:... atleast I go out in style....



Lucky mine was at the office.. That was a whole lot of AAA moving the car here to there, started off with just suspention but low oil pressure + me bounceing off the rev limiter in autocross + 130K miles = I havent driven my car sense new years. Unless you count the time I drove it from north end of town to the south after putting on new shocks/springs, and control arm, and listening to my crank bearing shot with the fork wacking all around.. If ya count that, then I drove it once sense new years eve :rofl:

I am having Rob at EFI build the engine, got to the point where I just want to give it to good hands and get the damn thing done. Also right, sense I want the thing to last another 100k miles
Chris at EFI is also going to tune it. He did a great autocross map for me, made more power on stock boost then I did on cobb's stage 2 map (not stock boost)

As seen in the video, my front quarter good a good wack, and I am sure the tranny is tweaked, or hopefully the seal is just craped. I also wanted to do the tranny first before a engine build.. I guess that plan has changed. For now I will just run 560CC and a vf39. **** my tranny!!!

I LOVE the vid!!!!! I need to make a vid of my car :D Holy lots of miles on the car!!! well It's good to know it lasted that long ya know! That is a long time not being able to drive the Subie.. I would go nuts!!!!:spin:

You are smart for going to EFI, They will do a great job, can't wait to see what you pull with the VF39! If I was smart i would do the tranny first.... but i really wanted to work on my motor. Well good luck and keep me posted



Found it

http://www.autosportsunlimited.com/remanufactured_european_asian_import_british_engin es.html
sweet!!! I checked it out and found the tranny. I just sent the link to scotty, see what he thinks.

Yes they do! Only $1700 too... Ashley.... :D I have it saved to my favorites... see what scott thinks...


What do you guys think???? Go for it???? :bull:

[Seraphinwolf]

STi 6mt ALL THE WAY!!!

[synergy]

See ladies. I dont joke :)

SO you think if i got it I would be able to sell it for atleast 3k :P
HAHA

[-III]

See ladies. I dont joke :)

SO you think if i got it I would be able to sell it for atleast 3k :P
HAHA

You could sell it for more if you find the right buyer, and have all the necessary bits for a complete swap.

[Bu11dogg2]

Ashley,

You need a 06/07 STi tranny if you don't want to change hubs ;)

[RCKSTR]

Ashley,

You need a 06/07 STi tranny if you don't want to change hubs ;)

This is true along with an automatic driveshaft! Be able to use your rear diff too :cool:

[jwebsta32]

Ashley,

You need a 06/07 STi tranny if you don't want to change hubs ;)

Or you can buy custom rear axles. Who would do that tho

[Bu11dogg2]

who spends $1200 on axles? idiots.... that's who

[Seraphinwolf]

Holding 800whp and reducing weight. Depends on what you are gonna do with the car.

[jwebsta32]

who spends $1200 on axles? idiots.... that's who


If you want a better rear and and not sourcing parts to swap to sti running gear you do

[synergy]

yeah the 06/07s are more expensive :(

And subaru brembos are expensive even for me. I was at one point going to buy some. They are around 600 for the fronts its crazy:spin:

[Bu11dogg2]

If you want a better rear and and not sourcing parts to swap to sti running gear you do


I was j/k :unamused:


I'm not making enough power to need it anyway :lol:

[RCKSTR]

yeah the 06/07s are more expensive :(

And subaru brembos are expensive even for me. I was at one point going to buy some. They are around 600 for the fronts its crazy:spin:


If I was to buy brembos I wouldn't pay more than $300...

Oh wait... :cool:

[Seraphinwolf]

I was j/k :unamused:


I'm not making enough power to need it anyway :lol:

:cool: You wish you were! Have you thought of trying H6 power? ;)

[Bu11dogg2]

to me, 300-350WHP is more than enough

[synergy]

FYI. I totally get a finders fee for a 1700$ sti tranny :lol:

[Midnight_Rush]

FYI. I totally get a finders fee for a 1700$ sti tranny :lol:


:lol: I wish I just had the money so I could go to a shop and be like here ya go now do the swap and I will watch and try to help. lol

i need to do some more research.. thanks for the headups on the year Randy.

custom rear axles would be nice!:D

[Instanced]

So from this entire thread, you haven't mentioned what actually happened... did someone else already state it? I'm curious what happened... timing? spun bearing? *Shrug*

[Midnight_Rush]

Not sure yet, All I know is its making a lot of noises... Scott at Ballistics will be working on my car. We are waiting for all of my parts to come in... Im waiting on the ACL bearings......There is a Thread on Nasioc stating why they are on back order.... Once I find out I will deff let everyone know!

[Bu11dogg2]

I would have gone with diff bearings if it was gonna take this long....

Cosworth/Crower

[Midnight_Rush]

I would have gone with diff bearings if it was gonna take this long....

Cosworth/Crower

Gary sent me a link and a few subie peeps were talking about the Cosworth/crower.... I am starting to think twice about ACL ::facepalm::

[Bu11dogg2]

get your money back, and your car back sooner

[shtbxr22]

I would have been done by now. :hide:

[Bu11dogg2]

updates?

I hear ACL = perm back order

[squeethebee]

Wouldn't a permanent back order just mean, out of business?

ed

[Bu11dogg2]

yes

[squeethebee]

:(

ed

[civic si hb]

I'm very intersted in seeing her car with the GT3071R. I think it's going to be a great DD turbo for her when we talked at the Japanese car show a few days ago.

[Midnight_Rush]

I'm very intersted in seeing her car with the GT3071R. I think it's going to be a great DD turbo for her when we talked at the Japanese car show a few days ago.

My bearings came in!!! :D

That was a fun day! I could deff go for some more italian ice!! :)

[shtbxr22]

it's a little late, but you could have............ http://www.importperformanceparts.net/imports/togabearings-subaru.html

[Midnight_Rush]

it's a little late, but you could have............ http://www.importperformanceparts.net/imports/togabearings-subaru.html


a tiny bit late Eric. lol :D

[shtbxr22]

sorry buddy. hope you can start getting that thing built.

[98Wagoon]

it's a little late, but you could have............ http://www.importperformanceparts.net/imports/togabearings-subaru.html

am I crazy or does that not list an ej20 application?

[shtbxr22]

it does appear that way.

[98Wagoon]

just making sure.. because.. well.. I am a bit crazy, as we know.. :lol: is this because the 205 and 257 use the same bearings? cuz.. well... the internet told me that once, if I remember..... and if ACL is finally sending bearings to customers again perhaps I should jump on that bandwagon real soon.... :shrug:

[Midnight_Rush]

My ACL bearings came in!!!

[Subyspeed]

whoohooooooo

[shtbxr22]

you posted that last page girl! :lol: progress?

[Midnight_Rush]

not yet, I have all of my gaskets, should be getting my oil pan any day now... Hey Eric I ordered my oilpan do I have to change the feedneck??

[AExiOn]

Damn at the rate your going, your going to be finished before me :rofl:

[Midnight_Rush]

Damn at the rate your going, your going to be finished before me :rofl:

HAH!!! :D


Do you know how much longer with yours?

[Bu11dogg2]

not yet, I have all of my gaskets, should be getting my oil pan any day now... Hey Eric I ordered my oilpan do I have to change the feedneck??


I'm pretty sure you need a longer dipstick IIRC

[AExiOn]

I am hoping before it gets cold out. I would like to imagine next month but, I still got some ways to go. My buddy who spun a bearing in his 02 this year already got his engine back, and he spun it in april :unamused: :rofl:

[Bu11dogg2]

I don't know how you gals/guys have so much patience :spin:

[axis]

^^^THIS. I would lose my **** if my car was down for that long.

[AExiOn]

I dont know about her.. But I want to ****ing kill people..
I havent had one of my 100 mile weekend joy ride in forever...

[Bu11dogg2]

if my motor **** the bed i'd have a 257 shortblock, install kit and used heads(if I needed them) in my posession in under a week.

[AExiOn]

Money and time my friend, money and time

[Bu11dogg2]

I have one and not the other :lol:

[itsmy04wrx]

This popped in my news feed on facebook from Ballistic Motorsports's photos.


http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs398.snc4/46152_431025419412_284870429412_4874624_1561828_n. jpg (http://www.facebook.com/photo.php?pid=3454162&id=284870429412)

[brian]

Oh yea! Parts are all here . I'm thinking in about a week it will be on the road!!

[shtbxr22]

still no word on what happened to the engine?

[RCKSTR]

still no word on what happened to the engine?

Chuck Norris is what happened to it... :lol:

[im_so_blue]

Chuck Norris is what happened to it... :lol:

http://itsguycode.com/images/stories/chuck-norris/chuck-norris-thumbs-up.jpg

[Midnight_Rush]

Money and time my friend, money and time true...true.... :unamused:

I have been going nuts...... :spin:

This popped in my news feed on facebook from Ballistic Motorsports's photos.


http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs398.snc4/46152_431025419412_284870429412_4874624_1561828_n. jpg (http://www.facebook.com/photo.php?pid=3454162&id=284870429412)

:D I may go to the shop tue morn or wed and clean my engine bay, while the motor is out! :)

Oh yea! Parts are all here . I'm thinking in about a week it will be on the road!!
IIIII hope so! :D

Chuck Norris is what happened to it... :lol: LMAO :lol: you can say that again. I should know tue or wed.

[Berge56]

holy hell progress!!! :hide:

Hopefully the car is done soon. :up:

[EvoBrett]

I was in ballistic today dropping off a part to be powder coated and ur engine looked to be getting put back together. The car was still on the lift so hopefully its being put back in soon!

[Subygirl8330]

this is so exciting!

[shtbxr22]

still using head studs?

[Bu11dogg2]

Nice!

I bet you're excited :)

[Instanced]

NICE :) looks really clean!

[Berge56]

any updates cuz?

[Midnight_Rush]

my engine bay is CLEAN, i have a few parts i was to powdercoat will do that next wed.. My interior is pretty much done!!! Suede headliner and pillars, black dome lights, black seatbelt covers.. I am going to order STI visors since they are black. I really dont want to mess with my stock ones.... all I need to do now is find 04 sti door cards, install my new deck, relocate my EDFC and interior will be DONE!!!! as for the Engine build.... lol Need to send 2.5 block out to have some machine work done! then we will be installing everything in! woot woot so maybe in December !!!! : o P

[Bu11dogg2]

why so long for the Machine work?

[Midnight_Rush]

III dont know.... It should only take a day or two to do.. I am just throwing a month out their since that's all I have been doing everytime someone asks me. lol I really hope it's going to be done by the end of this month...........................

[Berge56]

Sweet! Do you have any pics or the engine bay and interior?

[Bu11dogg2]

III dont know.... It should only take a day or two to do.. I am just throwing a month out their since that's all I have been doing everytime someone asks me. lol I really hope it's going to be done by the end of this month...........................


i'd hope so too :)

Machining heads takes about 4 hours and block work can be done relatively quickly from what i've seen :)

Where are you sending it to?

[shtbxr22]

what machine work is being done to the engine? also, what the heck caused the failure on the 2.0?

[Berge56]

So its been 2 weeks. Anything new?

[Bu11dogg2]

bumpdate?

[AExiOn]

yes whos winning the race to getting our bugeyes back on the road? :lol:

[Berge56]

ibetartwinstherace :hide:

[shtbxr22]

I say again.......I could have finished this last year. next time ash.....next time.

[Subygirl8330]

they sent the block to get rehoned and sleeved. and they took apart the old engine, but i dont think they had anytime to put it back together yet.

[im_so_blue]

yes whos winning the race to getting our bugeyes back on the road? :lol:

should we place a bet on who brings their bug eye to a certain event first running? :lol:

Mines still running! for now :P

gonna be out of sight next year for god knows how long as i will be having a buddy redo the body work on it for me. and have another do the interior. got some tricks up my sleeves for next year

[shtbxr22]

they sent the block to get rehoned and sleeved. and they took apart the old engine, but i dont think they had anytime to put it back together yet.


overkill anyone? i'm hoping this will be a 600hp monster. otherwise, probably a waste of cashola. I thought she was shooting for less than 400 at the wheel? :spin:

[Berge56]

they sent the block to get rehoned and sleeved. and they took apart the old engine, but i dont think they had anytime to put it back together yet.

Wow she should be good for 30psi +.




Watch out Brian! :lol:

[Subygirl8330]

hahaha well ya always gotta aim high!

[shtbxr22]

yeah, good luck blowing that one. :lol:

[Berge56]

Updates???

[Bu11dogg2]

+1 :)

ashleeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeey !

[hiprsha666]

I thought you were gonna have this done the week after supermeet? What happened?

[brian]

More parts were ordered and others were on back order . I got to drive it today !

[Seraphinwolf]

Well it better be ****ing amazing!

[Midnight_Rush]

My subie is Finally running!! :D The reason it took so long is because I kept ordering parts and we were waiting for other parts that were on back order to come in, Also trying to save money to buy parts.... lol
My bearings went in my car, nothing too too bad, so I was able to use my 2.0 heads. I havent been on the forum in a while nor driving my subie because I have been dealing with some issues.. :unamused:

overkill anyone? i'm hoping this will be a 600hp monster. otherwise, probably a waste of cashola. I thought she was shooting for less than 400 at the wheel? :spin:

Ya know sometimes you come off as a D-bag Eric :spin::D ... First you were ragging on me because I bought GTspec header, you told me my subie will now sound like a honda... You chuckeled because i'm going to get tuned at EFI... Now you're sayin overkill anyone?? I am getting the 2.5 block honed because it's brians old sti block... of course I am going to get it honed..... It's used.. My goal is to hit 400whp... Will I get there?? not sure...

[RCKSTR]

What turbo are you running now?? Did that change?

[jwebsta32]

I think he was more or less talking about the part where you said it was off to get honed and SLEEVED.

[hiprsha666]

**** it, go for 600. lol

[Midnight_Rush]

overkill anyone? i'm hoping this will be a 600hp monster. otherwise, probably a waste of cashola. I thought she was shooting for less than 400 at the wheel? :spin:

What turbo are you running now?? Did that change?
Yeah I am going to run the same turbo Garette 3071:D

I think he was more or less talking about the part where you said it was off to get honed and SLEEVED.
I never stated on here it was getting sleeved though..

**** it, go for 600. lol
Lets do it up!! :D Twin turbo?? :eek: lol

[jwebsta32]

they sent the block to get rehoned and sleeved. and they took apart the old engine, but i dont think they had anytime to put it back together yet.


your female friend did. and thats what he was saying was ridiculous

[hiprsha666]

Yeah I am going to run the same turbo Garette 3071:D


I never stated on here it was getting sleeved though..


Lets do it up!! :D Twin turbo?? :eek: lol

Twin turbo, its possible. I dare you. :lol:

[Seraphinwolf]

Yeah it's all Meg's fault!

[Midnight_Rush]

your female friend did. and thats what he was saying was ridiculous

I know, I was talking to Meg about "hone and sleeves" a while ago, but I decided not to do it at the last min. Hence me not Posting it up here. Just how Eric stated everything. What if I did do the sleeves... Why would it be overkill...??? I have known Eric for a while now.. Just stating he sounds like a D-bag, Doesnt mean I hate him and ill never talk to him again.....lol

[Vinyl Freaks]

not everything said on a forum is what actually happens.. oh no imagine that!


...now everyone huggg! :D

[Midnight_Rush]

your female friend did. and thats what he was saying was ridiculous

not everything said on a forum is what actually happens.. oh no imagine that!


...now everyone huggg! :D

:up:

[-III]

Did I miss the hug?

[Vinyl Freaks]

your just in time!

[-III]

:subygirl:

[shtbxr22]

My subie is Finally running!! :D The reason it took so long is because I kept ordering parts and we were waiting for other parts that were on back order to come in, Also trying to save money to buy parts.... lol
My bearings went in my car, nothing too too bad, so I was able to use my 2.0 heads. I havent been on the forum in a while nor driving my subie because I have been dealing with some issues.. :unamused:



Ya know sometimes you come off as a D-bag Eric :spin::D ... First you were ragging on me because I bought GTspec header, you told me my subie will now sound like a honda... You chuckeled because i'm going to get tuned at EFI... Now you're sayin overkill anyone?? I am getting the 2.5 block honed because it's brians old sti block... of course I am going to get it honed..... It's used.. My goal is to hit 400whp... Will I get there?? not sure...


No douchebaggery intended, but like stated earlier it appeared from megs post that you were overstrengthening things, but we talked about it after when we were snapping pics at that lot. I expected a hone too, so it was just about the sleeving. ;) And I chuckle about EFI, just because my pockets aren't deep enough. :lol: don't be offended, I still love ya'.

[shtbxr22]

I know, I was talking to Meg about "hone and sleeves" a while ago, but I decided not to do it at the last min. Hence me not Posting it up here. Just how Eric stated everything. What if I did do the sleeves... Why would it be overkill...??? I have known Eric for a while now.. Just stating he sounds like a D-bag, Doesnt mean I hate him and ill never talk to him again.....lol

And sleeving is for super duper powerful cars.

[Midnight_Rush]

Still love ya too Eric!!!! Lol yeah I don't have that much money!!! Otherwise I would be passing brian!! buhahahahah... But to me its worth getting tuned at EFI since my first tune was by TDC who recked my car.. Chris does a great job and I trust him with my subie

[shtbxr22]

That's all that matters, and you better give me a ride. It's gonna be faster than mine. :D

[Midnight_Rush]

I sure will!!! Can't wait to bring it on the kanc run!!!! : o D.

[im_so_blue]

i am here for the said hug........

wait . whats going on in here guys :iam:

[Berge56]

Congrats Cuz! So how is hse running? How many miles on the block?

[Midnight_Rush]

Congrats Cuz! So how is hse running? How many miles on the block?


Thanks CuZ:D She is running great! I can't drive it due to my leg...:spin:
and I will be working on my tranny soon... it has around 13k miles

[Bu11dogg2]

bumpdates?

[Midnight_Rush]

My motor build is complete! I will be going with the PPG setup in a couple months, then will get a tune in the spring by EFI. I will be posting new pics in the member gallery in 5.

[Berge56]

:munch: